Aufwachstechnik
Als Aufwachstechnik werden Verfahren zur zahntechnischen Wachsmodellation der Außenkontur von Kronen und Brückengliedern zur Herstellung von laborgefertigten Restaurationen bezeichnet. Besondere Bedeutung kommt dabei der funktionsgerechten Gestaltung des Kauflächenreliefs der Seitenzähne bei gegossenen Arbeiten zu. Je nach "Schule" (z.B. P.K. Thomas, Lundeen/Payne, Polz, Schulz) werden dabei verschiedene Zahnbeziehungen, Okklusionskonzepte, Höcker-Fossa-Relationen und Kontaktpunktmuster favorisiert.
Meist werden verschiedene anatomische Elemente (etwa Höckerspitzen, Randleisten, Höckerabhänge) einzeln (zu didaktischen Zwecken oft auch in unterschiedlichen Wachsfarben) nacheinander additiv aufgetragen.
Dazu müssen bei Zimmertemperatur feste Spezial-Wachse zunächst verflüssigt werden. Das kann in kleinen Portionen mit unterschiedlich geformten Arbeitsenden von Handinstrumenten ("Aufwachsinstrumente") in der offenen Flamme (etwa eines Gas-Brenners) oder zur genauen Temperatursteuerung und Vermeidung von Verunreinigungen mit elektrisch beheizten Schmelzeinrichtungen (z.B. elektrische Wachsmesser, Induktionsheizgeräte, Wachstauchdosen) erfolgen. Das Auftragen erfolgt tropfenweise, so dass das neue heißere, flüssige Material mit dem schon vorhandenen kälteren festen nahtlos verschmelzen kann.
Eine nachträglich Reduktion der Wachsmodellation durch "Schnitzen", Fräsen von Führungsflächen oder Bohrungen für Retentionselemente ist möglich.
In modernen Verfahrensvarianten stehen zur Ausformung erweichten Wachses auch vorgefertigte flexible Kauflächenformteile zur Verfügung. Daneben gibt es konfektionierte Fertigteile aus Wachs, etwa Kauflächen oder Brückenzwischenglieder in verschiedenen Formen und Größen. Statt reversibel thermoplastischer Wachse können in neuerer Zeit auch irreversibel lichthärtende Materialien verwendet werden.
Wachsfertigteile
Modelloberflächen, Gegenbezahnung, Nachbarzähne und Kronen-/Pfeiler-Stümpfe müssen mit speziellen Lacken (die aufgesprüht, aufgestrichen oder durch Tauchen aufgebracht werden) verfestigt und/oder isoliert werden, um die Wachsmodellation später zerstörungsfrei abheben zu können. Dazu sind auch die verwendeten Wachse nach Erkalten meist relativ starr-elastisch.
Anbringen von Wachsgußkanälen an einer Doppelkronensekundärkonstruktion
Um verlorene Formen für Gussverfahren zu gewinnen, werden Wachsmodellationen mit aus Wachs vorgefertigten Gusskanälen, -Balken, und Reservoiren versehen. Nach dem Abnehmen und "Anstiften" an den Gusstrichterformer folgt in einer Muffel das Einbetten in einer erhärtenden feuerfesten Masse. Das Wachs kann anschließend rückstandsfrei ausgebrannt werden und der Gussvorgang folgen.
Ein "Wax-Up" dient anders als A. meist nicht unmittelbar der Umsetzung in eine indirekte Restauration, sondern der Simulation des späteren Aussehens und/oder der äußeren Form zur Herstellung orientierender Schablonen.
... or need professional advice?
Get in touch with us or click Contact.
English | German |
---|---|
set of cutters | Fräserset |
Composites also composite (from the Latin componere = to compose) are tooth-coloured filling materials with plastic properties used in dental treatment. In lay terms they are often referred to as plastic fillings, also erroneously sometimes confused with ceramic… Composites also composite (from the Latin componere = to compose) are tooth-coloured filling materials with plastic properties used in dental treatment. In lay terms they are often referred to as plastic fillings, also erroneously sometimes confused with ceramic fillings due to their tooth colour. After being placed in a cavity they cure chemically or by irradiating with light or a combination of the two (dual-curing). Nowadays, composites are also used as luting materials. The working time can be regulated with light-curing systems, which is a great advantage both when placing fillings and during adhesive luting of restorations. Dual-curing luting materials are paste/paste systems with chemical and photosensitive initiators, which enable adequate curing, even in areas in which light curing is not guaranteed or controllable. Composites were manufactured in 1962 by mixing dimethacrylate (epoxy resin and methacrylic acid) with silanized quartz powder (Bowen 1963). Due to their characteristics (aesthetics and advantages of the adhesive technique) composite restorations are now used instead of amalgam fillings.
The material consists of three constituents: the resin matrix (organic component), the fillers (inorganic component) and the composite phase. The resin matrix mainly consists of Bis-GMA (bisphenol-A-glycidyldimethacrylate). As Bis-GMA is highly viscous, it is mixed in a different composition with shorter-chain monomers such as, e.g. TEGDMA (triethylene glycol dimethacrylate). The lower the proportion of Bis-GMA and the higher the proportion of TEGDMA, the higher the polymerisation shrinkage (Gonçalves et al. 2008). The use of Bis-GMA with TEGDMA increases the tensile strength but reduces the flexural strength (Asmussen & Peutzfeldt 1998). Monomers can be released from the filling material. Longer light-curing results in a better conversion rate (linking of the individual monomers) and therefore to reduced monomer release (Sideriou & Achilias 2005) The fillers are made of quartz, ceramic and/ or silicon dioxide. An increase in the amount of filler materials results in decreases in polymerisation shrinkage, coefficient of linear expansion and water absorption. In contrast, with an increase in the filler proportion there is a general rise in the compressive and tensile strengths, modulus of elasticity and wear resistance (Kim et al. 2002). The filler content in a composite is also determined by the shape of the fillers.
Minimally-invasive preparation and indiscernible composite restoration
Composite restorations Conclusion |